MR4SF MOTIVE-RC S-FHSS Receiver 6.8ms High Speed 4CH Compatible Futaba SFHSS 10PX 4PLS 4PX 4PM 14SG #MR4SF

MR4SF MOTIVE-RC S-FHSS Receiver 6.8ms High Speed 4CH Compatible Futaba SFHSS 10PX 4PLS 4PX 4PM 14SG 18MZ Radio

Thank you for purchasing MOTIVE-RC's S-FHSS compatible receiver. This production can supply enhancement smooth drive with FUTABA S-FHSS link.

Compatibility:

MOTIVE-RC 2.4GHz S-FHSS Compatible Receiver is designed to use withFUTABA S-FHSS2.4GHz transmitters, such as surface systemT3PV, 4PLS, T4PX, T4GRS, T4PM, T4PV, T7PX, T10PXor air systemT4YF, T6J, T6K, T8J, T10J, T14SG, T18MZ, T18SZunder S-FHSS protocol mode.

Feature:

• 4ch servo channels on CH1~CH4

• S.BUS output support expanding servo channels on the 5th channel.

• Normal mode and High Speed mode.

• Support Fail-safe function on all channels

Specifications:

• Model Type: RC Car/Boat

• Operating Current: 20mA max and 10mA under linked

• Antenna: Built-in antenna

• Operating Voltage:  3.6~8.5V

• Operation temperature: - 10~70 degC

• Weight: 7.2g

• Size: 20.5x18.5x28.8 mm

• Latency: 6.8ms(High Speed mode) or 13.6ms(Normal mode)

Bind procedure:

1. Insert the bind cable into the receivers “BIND”channel, plug the power cable into any other channel.

2. Turn on the S-FHSS transmitter, leave it 0.5M~1M away the receiver.

3. Red LED light on and Green LED off when searching signals, and turn to Green LED light on and Red LED off indicate bind is succeeded.

4. Remove the power and bind cables from the receiver, reconnect the power cable to the receiver.

5. Check to make sure that the transmitter and receiver are working as expected, if there are any issues or unexpected operation follow the steps above to bind again.

Fail-safe setting:

MR4SF set failsafe on the S-FHSS transmitter just like the operation of the FUTABA receivers if the feature exist. We highly recommend you set failsafe feature while driving your models. An example of a useful failsafe setting would be to shut down the model's throttle, so that it does not drive away uncontrolled.

High Speed/ Normal mode switch guide:

The "Normal mode" accepts any type of servos or the peripheral. The "High Speed mode" only accepts the digital servos, including BLS series, and most peripheral equipment such as the brushless ESC. Please pay special attention to the information contained within this manual and transmitters manual in order to have a pleasant running experience.

If your receiver has been linked with your transmitter, please power off your transmitter. When your receiver's LED light red, insert the bind cable into the receivers “BIND”channel for more than 6 seconds but no longer than 10 seconds. Remove the bind cable and you will see the green LED blinking slowly.

Now insert the bind cableagain, and the receiver will first blink the red LED and then turn off, followed by the green LED blinking. (Pay attention to the speed of the green LED flashing, as this indicates the receiver's working mode).

When the green LED blinks slowly, it means the receiver has switched from high-speed mode to normal mode; when the green LED blinks quickly, it means the receiver has switched from normal mode to high-speed mode.

After about 6 seconds, the green LED will turn off, and the red LED will stay on, indicating that the mode switch is complete.

Note:If you want to reset the receiver to normal mode, you can rebind the receiver to the remote control.

LED status indicated under normal working status:

Package included:

1 * MR4SF receiver

1 * bind cable